|
Product Details:
Payment & Shipping Terms:
|
High Light: | usb to serial cable converter,usb to serial converters |
---|
USB To RS485 Converter
Standards:Conforming to USB1.1, 1.0 and 2.0 standards and EIA RS-485 and RS-422 standard
USB signals:VCC, DATA+, DATA-, GND and FG
RS-485 signals:T /R+,T/R-,GND
Baud rate:300-128000bps, automatically detecting the data rate
USB interface is gradually replacing the old-fashioned low-speed peripheral interfaces of PC with the continuous development of PC industry. But many vital devices in current industrial environment is still designed using RS-485/RS-422 interface, so the USB to RS-485/RS-422 converters are needed to transfer data between PC and RS-485/RS-422 devices.
UT-861 is a universal USB/RS-485/422 converter which doesn’t need external power supply and has built-in opto-isolator and DC/DC power isolation module. It is compatible with USB ,RS-422 and RS-485 standards, and it can convert single-end USB signal to balanced differential RS-422 or 485 signal. The built-in photoelectric isolator can provide isolating voltage up to 2500Vrms and it equips with high-speed transient voltage supressor which is designed to protect the RS-422/RS-485 interface. The advanced TVS (TRANSIENT VOLTAGE SUPPRESSOR) presents high-impedance state under normal conditions, and it can rapidly decrease the resistance between its two ends while it’s withstanding transient high-power impulse so as to absorb the high current and clamp the voltage across it to a preset value, and then the following components will not be damaged by the transient high-voltage impulse. This suppressor can effectively restrain lightning and ESD (electro-static discharge) with lightning surge protection power of 600W for each line, and it also can restrain surge voltage and transient over-voltage on the lines for any reason. Extremely small interelectrode capacitance ensures high speed data transmission of RS-422/RS-485 interface.The RS-422/RS-485 end is connected through male DB9 connector.It has built-in automatic transmit-receive switch without time delay. The unique I/O circuit can be used to automatically control the direction of data flow without any hand-shaking signals(such as RTS and DTR) and full-duplex(RS-422) and half-duplex (RS-485) can be implemented without jumper configuration,so as to make it plug-and-play and applicable to all existing communication software and interface hardware.
UT-861 industrial photoelectric isolated interface converter can provide reliable connection for point-to-point or point-to-multipoint communication. Maximum 128 RS-422 or RS-485 interface devices can be supported for the point-to-multipoint communication. Data communication rate can be 300-128000BPS, and the power indicator light and data traffic indicator light can be used for malfunction indication. USB to RS-422 and USB to RS-485 conversions are supported.
Specifications:
Standards |
Conforming to USB1.1, 1.0 and 2.0 standards and EIA RS-485 and RS-422 standard |
USB signals |
VCC,DATA+,DATA-,GND,FG |
RS-485 signals |
T /R+,T/R-,GND |
RS-422 signals |
T/R+,T/R-,RXD+,RXD-,GND |
Operating mode |
Asynchronous mode, point-to-point or point-to-multipoint mode, 2-wire half-duplex, 4-wire full-duplex |
Data flow control |
Automatic data flow control technique is adopted to automatically determine and control the data flow |
Baud rate |
300-128000bps, automatically detecting the data rate |
Load capacity |
point-to-multipoint communication mode is supported, maximum 128 RS-422 or RS-485 devices are supported |
Communication distance |
5000 meters for RS-485/422 interface (128000bps-9600bps) and no more than 5 meters for the USB port |
Interface protection |
600W lightning and surge protection for each port, ±15KV ESD portection |
Isolation degree |
2500Vrms isolation voltage for each port, 500DC contineous specialized DC/DC module |
Isolation type |
master/slave isolation, slave/slave isolation |
Interface connection |
B type female connector at USB side and DB9 male connector at RS-485/422 side |
Signal indication |
9 signal indicator lights Power(PWR) transmit (TXD) receive (RXD) |
Transmission media |
twisted-pair or shielded cable |
Baud rate
|
128000bps to 300M 38400bps to U2.4KM 9600bps to U5KM |
Dimension |
210mmX130mmX32mm |
Environmental parameters |
temperature of -25°C to 70°C, relative humidity of 5% to 95% |
Supported OS |
Win98/Win2000/WinXP/Win7/Linux |
Connector and signals
DB9 PIN type: signal output and pin assignment of RS-485/RS-422
DB9 PIN type(PIN) |
Signal output |
RS-422 full-duplex connection |
RS-485 half-duplex connection |
1 |
T/R+ |
Transmit (A+) |
RS-485 (A+) |
2 |
T/R- |
Transmit(B-) |
RS-485 (B-) |
3 |
RXD+ |
Receive(A+) |
Not connected |
4 |
RXD- |
Receive(B-) |
Not connected |
5 |
GND |
Ground |
Ground |
6 |
N/A |
|
|
7 |
N/A |
|
|
8 |
N/A |
|
|
9 |
N/A |
|
|
Contact Person: Mr. Brandy Xie
Tel: +86-755-27886063 Ext.602
Fax: 86-755-27886083